www2.fishmansupply.com friday 03/23/2018 20:00:15
23 Mar 2018 20:00:14 Starting file-save on www2.fishmansupply.com
/usr/bin/d3 USAGE:
/usr/bin/d3 {arg1 {arg2 {...}}} {line} {cfg} {tty}
Where argN matches one of the following:
-? Prints this usage info
-D Start in monitor debugger. Break goes to monitor debug first
-L lang Language file to use
-T read serial commands from file
-V Print monitor, flash and SQL versions, and quit right away
-W Wait for the device.
-a Auto boot. Will be line 0, and there will be no prompt
-b Absprotect off - allows installing abs patches
-d 'cmds' Stack 'cmds' into the D3 input buffer. Use \r for CR
-dcdoff Forces DCD protocol off.
-dcdon Forces DCD protocol.
-f* Restart memory flusher
-haforcecheck Force the checking of logon credentials
-hotbackup* This port is a hot-backup process.
-i val Set nice value to 'val'
-icrlf Ignore lf after cr for turnkey telnet.
-k* Kill the virtual machine.
-key key Specify virtual machine 'key'
-l Ignore the 'user' command in the configuration file
-m* Restart signaler process
-n name Specify configuration file 'name'
-osfiserv* Used to start osfi servers. Do not use by hand.
-p* Obsolete phantom scheduler option. Do not use.
-phantom* This port is a phantom.
-pprinter* This port is a parallel printer.
-printer* This port is a printer.
-q Print virtual machine information
-qf Print flusher information
-ql Print license connection information
-qn Print network connection information
-r Reset the port before executing
-rawdiskoff Disable raw disk processing for one process
-restorex Enable extended restore options
-s Silent mode
-scheduler* This port is the phantom scheduler.
-spooler* This port is the spooler.
-t ttyname Specify 'ttyname' as the tty file to use
-ts Manual tape server.
-u Leave process unlinked.
-v val Set logging Verbosity level to 'val'
-y Change stty info. Multiple -y options are okay
* these commands are not normally used during day to day operations
-DEBUG* Allow monitor debugging. Reserved for Rocket Software.
Any command line input that is not associated with an option specified
above will be interpreted as:
o 1) A pib number if it's numeric, or
o 2) A config file name if one has not already been specified, or
o 3) A TTY name if one has not already been specified, or
o 4) cause the d3 command to abort and display this usage message
23 Mar 2018 20:00:15 D3 backup complete
23 Mar 2018 20:00:15 File-save has been archived to /u/bkup/friday
23 Mar 2018 20:00:15 File-save is 14 Mb (15069466 bytes), 1 file
23 Mar 2018 20:00:15 FTP to mail3.pfinders.com starting
23 Mar 2018 20:00:15 FTP user fishman
23 Mar 2018 20:00:23 FTP sent /u/bkup/friday (15069466 bytes)
23 Mar 2018 20:00:23 FTP to mail3.pfinders.com complete.
23 Mar 2018 20:00:23 FTP throughput 1839 Kb/s.
23 Mar 2018 20:00:23 Archiving system files to system_files.tar.gz
23 Mar 2018 20:00:23 File system_files.tar.gz is 774 Kb
23 Mar 2018 20:00:23 FTP to mail3.pfinders.com starting
23 Mar 2018 20:00:23 FTP user fishman
23 Mar 2018 20:00:23 FTP sending single file system_files.tar.gz
23 Mar 2018 20:00:24 FTP sent /u/bkup/system_files.tar.gz (793154 bytes)
23 Mar 2018 20:00:24 FTP to mail3.pfinders.com complete.
23 Mar 2018 20:00:24 D3 backup took 0 hrs 0 mins 9 secs
23 Mar 2018 20:00:24 Cleaning nulls from display log. Log file may shrink
23 Mar 2018 20:00:26 No GFE's encountered
23 Mar 2018 20:00:26 Warning: File-save did not verify using T-VERIFY command. Backup may be bad.
23 Mar 2018 20:00:26 Posting data to http://monitor.pfinders.com/report.php
Performed by d3backup version 3.82