Back to list

23 Mar 2018 20:00:14 Starting file-save on www2.fishmansupply.com
/usr/bin/d3 USAGE:
/usr/bin/d3 {arg1 {arg2 {...}}} {line} {cfg} {tty}
 Where argN matches one of the following:
  -?          Prints this usage info
  -D          Start in monitor debugger.  Break goes to monitor debug first
  -L lang     Language file to use    
  -T          read serial commands from file
  -V          Print monitor, flash and SQL versions, and quit right away
  -W          Wait for the device.
  -a          Auto boot.  Will be line 0, and there will be no prompt
  -b          Absprotect off - allows installing abs patches
  -d 'cmds'   Stack 'cmds' into the D3 input buffer.  Use \r for CR
  -dcdoff     Forces DCD protocol off.
  -dcdon      Forces DCD protocol.
  -f*         Restart memory flusher 
  -haforcecheck Force the checking of logon credentials
  -hotbackup* This port is a hot-backup process.
  -i val      Set nice value to 'val'
  -icrlf      Ignore lf after cr for turnkey telnet.
  -k*         Kill the virtual machine.
  -key key    Specify virtual machine 'key'
  -l          Ignore the 'user' command in the configuration file
  -m*         Restart signaler process
  -n name     Specify configuration file 'name'
  -osfiserv*  Used to start osfi servers.  Do not use by hand.
  -p*         Obsolete phantom scheduler option.  Do not use.
  -phantom*   This port is a phantom.
  -pprinter*  This port is a parallel printer.
  -printer*   This port is a printer.
  -q          Print virtual machine information
  -qf         Print flusher information
  -ql         Print license connection information
  -qn         Print network connection information
  -r          Reset the port before executing
  -rawdiskoff	Disable raw disk processing for one process
  -restorex   Enable extended restore options
  -s          Silent mode
  -scheduler* This port is the phantom scheduler.
  -spooler*   This port is the spooler.
  -t ttyname  Specify 'ttyname' as the tty file to use
  -ts         Manual tape server.
  -u          Leave process unlinked.
  -v val      Set logging Verbosity level to 'val'
  -y          Change stty info.  Multiple -y options are okay
 * these commands are not normally used during day to day operations
 -DEBUG* Allow monitor debugging.	Reserved for Rocket Software.
 Any command line input that is not associated with an option specified
 above will be interpreted as:
 o   1) A pib number if it's numeric, or
 o   2) A config file name if one has not already been specified, or
 o   3) A TTY name if one has not already been specified, or
 o   4) cause the d3 command to abort and display this usage message
23 Mar 2018 20:00:15 D3 backup complete
23 Mar 2018 20:00:15 File-save has been archived to /u/bkup/friday
23 Mar 2018 20:00:15 File-save is 14 Mb (15069466 bytes), 1 file
23 Mar 2018 20:00:15 FTP to mail3.pfinders.com starting
23 Mar 2018 20:00:15 FTP user fishman
23 Mar 2018 20:00:23 FTP sent /u/bkup/friday (15069466 bytes)
23 Mar 2018 20:00:23 FTP to mail3.pfinders.com complete.
23 Mar 2018 20:00:23 FTP throughput 1839 Kb/s.
23 Mar 2018 20:00:23 Archiving system files to system_files.tar.gz
23 Mar 2018 20:00:23 File system_files.tar.gz is 774 Kb
23 Mar 2018 20:00:23 FTP to mail3.pfinders.com starting
23 Mar 2018 20:00:23 FTP user fishman
23 Mar 2018 20:00:23 FTP sending single file system_files.tar.gz
23 Mar 2018 20:00:24 FTP sent /u/bkup/system_files.tar.gz (793154 bytes)
23 Mar 2018 20:00:24 FTP to mail3.pfinders.com complete.
23 Mar 2018 20:00:24 D3 backup took 0 hrs 0 mins 9 secs
23 Mar 2018 20:00:24 Cleaning nulls from display log. Log file may shrink
23 Mar 2018 20:00:26 No GFE's encountered
23 Mar 2018 20:00:26 Warning: File-save did not verify using T-VERIFY command. Backup may be bad.
23 Mar 2018 20:00:26 Posting data to http://monitor.pfinders.com/report.php

Back to list

Performed by d3backup version 3.71